Ask for JOE or GEORGE MILLS
email: pizzaovens@aol.com .. phone: (800) 356-2506 .. fax: (734) 458-8860

XLT OVEN
FEATURES

Most consumers are looking for products that perform extremely well at a very low cost. That was the design criteria used for the XLT ovens. By using fewer components of a higher quality, XLT ovens out-perform most other ovens, in terms such of initial purchase price, performance, and durability.
 

Standard Features
The XLT ovens have all of the same basic features found in other popular designs, including:
 

 
Enhanced Features
The XLT design has additional features that make it superior to all other ovens on the market.
 

Standard Parts
Most manufacturers will use special motors, valves, or controls. When you need parts and/or service, there is only one place to get them, and that is the original manufacturer of the appliance.

We use standard, off-the-shelf components that are available from industrial suppliers such as Grainger. We still use parts made by GE, Honeywell, and other top brands, but at a fraction of the cost because they are standard not custom.
 

Stainless Steel
The US Commerce Department defines a "Durable Good" as a manufactured item, such as a car or an appliance that typically lasts at least 3 years. The Pizza industry is approximately 40 years old and has used conveyor ovens only in the last 20 years. There are many pizza chains that use rebuilt ovens. We have seen Middleby Marshall and Lincoln ovens that have rust and cracks. In the very near future, these ovens will be in the scrap yard, their value reduced to almost nothing. The XLT oven bake chamber is 100% Stainless Steel. These ovens should last many times longer and be worth more money than ovens that rust and crack.
 

Stainless Steel vs. Aluminized Steel
Aluminized steel is similar to galvanized steel. Both are carbon steel sheets that have a thin layer of either aluminum or zinc applied to the surface to protect against rust. Most other oven manufacturers use aluminized steel for the interior and back of their ovens. This is less expensive, but not nearly as durable. Most oven cleaners contain a caustic solution that will literally dissolve the soft aluminum coating quickly. Also, scrapers or brushes will remove the thin layer of aluminum. Once this aluminum coating is gone, then rust (cancer) will form and the value and performance of the oven will diminish.

XLT bake chambers, fronts, control boxes, and fingers are constructed of 100% stainless steel. The backs and conveyors are constructed of about 99% stainless steel. This material will not succumb to oven cleaners, brushes, or scrapers. Stainless steel can be made to look like new even after many years of service and cleaning.

Once any "durable good" starts rusting, its value becomes questionable. XLT ovens are designed and built to out-last and out-perform all other ovens on the market. XLT ovens are worth more in the long term at a fraction of the price.
 

Bearings
We have rebuilt hundreds of Lincoln and Middleby Marshall ovens. The conveyor bearings we have seen are 1/2", 5/8", or 3/4" in diameter. Of the 1/2" bearings, we have seen about a 90% failure rate. The 5/8" bearings experience about a 50% failure rate. We have not seen a failure yet on a 3/4" bearing.

XLT ovens use 3/4" diameter bearings on the conveyor shafts. Clearly these will out-last and out-perform other oven designs. They will require less maintenance and will have less downtime. XLT ovens are worth more in the long term at a fraction of the price.
 

Fuses
Fuses protect components. Airplanes and other high quality goods are designed so that a failure of one component will not disable another component. For example, if a motor "shorts out", it could damage the control that is driving it if there is not a fuse between them. We have seen many ovens that either don't have fuses in the proper place, or they are buried inside the control boxes. All of our fuses are panel mounted. This means that anyone can replace a fuse, not just qualified service companies that have been known to charge as much as $150 for a service call. Our fuses are available at Radio Shack for less than $1.
 

Clean-ability
The entire front panel comes off in seconds with just 4 stainless steel knobs, no tools required. The fingers come out the front even faster. And since we use 100% Stainless Steel, you can use more aggressive oven cleaners to shorten the cleaning time involved.
 

Efficiency
The US national average cost for electricity is 8.3 cents per kilowatt-hour (KWh). A Watt is a measure of electrical power and equals volts times amps. A watt-hour is the number of watts used per hour. For example, if you used ten, 100-watt light bulbs for 1 hour, you used 1000 watts for 1 hour or 1 KWh. The comparison below shows the difference between the Middleby 555 oven and the XLT-3255 oven. We assumed a 12-hour day, and a 360-day year.

The XLT oven uses 1/4 of the amount of electricity that the Middleby uses. Or, stated another way, it is 400% more efficient. Currently, the annual savings is $774.49. As electricity rates continue to increase, it is conceivable that annual savings will approach $1000 per year. After 10 years, the savings alone could pay for your XLT ovens.
 

Maintenance
XLT ovens have no grease fittings that need regular service nor fan belts that can break putting you out of business until service arrives or can stretch, causing poor performance

Joe and George Mills
Representing Olender Equipment

Call 1-800-356-2506 or email pizzaovens@aol.com

New
Reconditioned
and Used

Pizza Ovens
Dough Mixers, Sheeters, Rollers

New
Make-Lines, Prep Tables,
Pizza Warmers

New
Refrigerators, Freezers,
Glass Door Merchandisers,
Coolers, Deli Cases

Pizza Shop Layout and Design Services.

Ventilation Issues Solved!

For questions or information about Pizza Equipment, Restaurant Equipment, or other content found on this site, please send mail to pizzaovens@aol.com.
Send mail to info@mbtonline.com with questions or comments about viewing issues or the design of this web site.
Copyright 2005, Site and content are property of Joe and George Mills.